by signing this document you are accepting the conditions set within. your requirements must be listed within this drawing. where no direction from the customer is identified samtec's process requirements will be used. date: company: customer signature: printed name: phone no: exceptions: other assembly packaging process tooling component non standard x do not scale from this print .356 9.04 ref .686 ref 17.42 .035 0.89 ref .810 ref 20.57 .040 ref 1.02 (typ) .451 11.46 "a" "a" 1 .880 ref 22.35 (((26 pos / 26) x .840[21.34]) + .040[1.02]) .320 8.13 ref .173.020 4.380.51 .535 ref 13.59 .275 6.99 ref .009 0.23 ref .0825 2.096 ref .625 15.88 25 eq spaces @ .0250[.635] c1 c2 4 c l 02 01 item no. part number quantity material 1 qfss-26-06.25-d-01-a 1.0000 vectra e130i, color: black 2 c-223-06.25-s 52.000 phos bronze, 521 extra spring temper 3 t-1g28-06.25-l 1.0000 phos bronze, 510 full hard temper 4 ppp-51 1.0000 46hf5040, color: black 5 ty-qfs012-026-6.25 1.0000 black hips c sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01[.3] 2 .xxx: .005[.13] .xxxx: .0020[.051] elevated qfs by: ASP-129646-01 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 12/13/2006 2 1 sheet scale: 2.5:1 c:\enterprisevault\dwg\misc\mktg\ASP-129646-01-mkt.slddrw plating: contact area: .000030 gold over .000050 nickel remainder: .000200 ref tin over .000050 nickel notes: 1. not available as standard. 2. represents a critical dimension. 3. burr allowance: .0015[0.038] max. 4. minimum pushout force: signal: .5 lb, ground: 1 lb. 5. max variance of .002[0.05]. 6. dimension applies to contacts & ground plane. 7. ground plane press height must be .003[0.08] less than the max height or .001[0.03] greater than the minimum height of the contact. 8. parts to be packaged in trays. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision b
.004 0.10 .134 (measured 3.40 contact to contact) .371 - .002 + .004 9.42 - 0.05 + 0.10 (see notes 5, 6, & 7) .050 1.26 ref .320.006 8.130.15 (applies to contacts) section "a"-"a" c5 c4 c7 (see note 6) 3 2 item 4 not shown for clarity .004[0.10] .371 - .002 + .004 9.42 - 0.05 + 0.10 (see note 5) in-process (see note 6) view .004[0.10] .340 8.64 .085 (typ) 2.16 .016 0.41 .710 18.03 .046 npth 1.17 (typ 2 plcs) .080 2.03 .025 0.64 .810 20.57 .020 0.51 .625 15.88 01 02 recommended pcb layout c l (all dimensions are symmetric about the centerline) sheet of elevated qfs by: ASP-129646-01 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. clay w 12/13/2006 2 2 sheet scale: 5:1 ASP-129646-01 c:\enterprisevault\dwg\misc\mktg\ASP-129646-01-mkt.slddrw revision b 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|